The Farr 11.6 (often listed as Farr 38) is a Bruce Farr design from the late 1970s that sits in the classic era when Farr was refining light, easily driven hulls for both offshore handicap racing and sensible cruising. At roughly 11.66 metres overall, the boat balances a relatively narrow waterline and a fine entry with enough beam and ballast to provide stiffness and carrying power for an extensive sailplan. Early examples were built using the materials and methods common to that period — cold‑moulded timber/ply and GRP combinations — and many surviving boats have been updated with modern sails, deck gear and systems to keep them competitive and comfortable.
This guide focuses on the design, layout, performance characteristics, typical Australian uses, and ownership considerations that apply specifically to the Farr 11.6. Where modern refits or local variations are common, those are noted. The aim is to give Australian buyers, owners and sailors a usable reference that explains why specific features matter afloat and what to inspect when considering a second‑hand purchase.
Overview and design purpose
Bruce Farr’s 11.6 was developed as a fast, seaworthy cruiser‑racer intended to perform well under rating systems of the era without sacrificing liveability for weekend or coastal cruising. It is neither an extreme light‑air scow nor a heavy displacement bluewater cruiser — instead it occupies the middle ground. The naval architecture emphasises low wetted surface for light‑air acceleration, a balanced sail plan for good pointing ability, and a fin keel plus spade rudder for responsive helm feel and manoeuvrability.
Practically, that meant owners could campaign their Farr 11.6s in club and offshore events (including Sydney‑Hobart fleets in the era) and still maintain accommodation for a small family or cruising couple. The boat’s motion and design made it attractive to owners who wanted a competitive boat that didn’t demand the all‑out crew work of pure racing yachts.
Designer, builder and production
Designer: Bruce Farr (Farr Yacht Design). The Farr 11.6 is often recorded under Farr design number 72 and commonly referred to as the Farr 38 in databases and marketing material. Farr’s reputation in the 1970s and 1980s was built on fast offshore racers that also adapted well to cruiser‑racer roles; the 11.6 follows that lineage.
Builder: production was undertaken by a small number of yards and builders in different markets. Records indicate builders such as Spindrift Yacht Inc (Canada) and other regional yards constructed examples; there are also boats built in South America under licence or contract. Reported build numbers vary by source, and many boats were finished or fitted locally by owners or brokers. This means construction detail and finish level can vary from one boat to another depending on the original yard and subsequent refits.
Production period: the design first appeared in 1978. Several dozen boats were built in the late 1970s and into the 1980s; some listings and registries report production totals in the dozens rather than hundreds. In practice, availability today is limited to second‑hand boats and occasional brokerage listings.
Construction and hull design
Hull form: the Farr 11.6 uses a fin keel with a spade (balanced) rudder and a moderately fine forefoot. The hull lines favour a relatively narrow waterline compared with more modern wide‑beam racers, with sufficient beam carried aft to give form stability under sail. The underwater profile aims to reduce wetted surface for light airs while providing righting moment through ballast for heavier conditions.
Keel and rudder: original builds used a fixed fin keel with a moderate (for the era) draft around 1.93–1.98 metres (6.3–6.5 ft) depending on specific keel casting and builder details. The spade rudder is internally mounted and gives quick, direct helm response. These appendages make the boat manoeuvrable and agile but mean that grounding or impact damage to the rudder or keel bulb/foil should be a primary inspection focus.
Construction methods and materials: many original hulls were constructed from fibreglass (GRP) with some cold‑moulded timber or wood trim in the interior. Resin systems and lay‑ups from the period vary; some boats employed hand lay‑up glass with balsa or timber coring in decks and superstructures. Because construction standards and materials differ by yard and owner refit, careful inspection for core rot, blistering, structural repairs and deck compression is essential on any used example.
Specifications
Cockpit, deck layout and sail handling
The Farr 11.6’s cockpit and deck layout reflect its dual role. Cockpit ergonomics favour a reasonably deep, well‑protected seating area for cruising comfort, while winch and control placement accommodate race crews. Many original boats were fitted with primary winches on the coachroof or coamings and halyard leads back to the mast or a central winch on the cabin top.
Short‑handed handling: the fractional rig and reachable mainsheet traveller mean the boat can be handled short‑handed with sensible sail choices. Headsails are typically moderate‑to‑large genoas for light air and smaller headsails or jibs for reaching and heavier conditions. On many boats, modern upgrades include self‑tending furling for headsails, roller‑furling headsails and single‑line reefing for the main — all useful changes for shorthanded cruising.
Deck movement: the coachroof and side decks are manageable for passage making; handholds and stanchions are placed for safe movement, but older decks may have timber or balsa coring under non‑skinned areas that need inspection. Cockpit tiller or wheel arrangements vary with fitout; a wheel offers easier long‑distance steering but can take space in the cockpit, whereas a well‑arranged tiller maintains direct feel and is simpler to maintain.
Interior and accommodation
Interior layouts of the Farr 11.6 generally provide a forward vee‑berth, a central saloon with facing settees that can convert to additional berths, and aft quarter berths on either side — a common layout for cruiser‑racers of the period. Construction used quality timber trim on many boats, with teak or mahogany joinery in better‑finished examples.
Galley and heads: the galley is usually compact and set to port or starboard near the companionway to make provisioning and cooking practical while at anchor. Heads are enclosed and, depending on the fitout, include a shower. Tankage for fresh water was comparatively generous in some original installations — several hundred litres in some examples — making the 11.6 able to undertake extended coastal cruises without frequent water stops (but tank capacities and plumbing should be confirmed on any specific boat).
Ventilation and light: opening hatches and opening ports give reasonable ventilation, though older boats often benefit from upgraded ventilation hardware or modern fans. Headroom is typical for a boat of this era and length: comfortable for sitting and moving around the saloon and galley, less generous standing headroom in some companionway and passage areas compared with contemporary cruiser‑orientated yachts.
Sailing and handling
Performance character: the Farr 11.6 is best described as a responsive, upwind‑orientated hull with lively acceleration in moderate winds and a rewarding helm. The fractional rig permits efficient mainsail trim and good upwind form; combined with a reasonable sail area to displacement ratio for the era, the boat performs well to windward and on close reaches.
Balance and helm: with a properly tuned rig and reefing plan, the boat carries sail without excessive weather helm. The fin keel and spade rudder give a direct helm and allow quick course corrections — useful when racing in crowded starts or when dodging shipping in coastal passages. In stronger winds the boat will demand reefing earlier than a heavy cruiser, but that is a trade‑off for better light‑air performance.
Sea manners: the hull tends to have a comfortable motion for offshore passages and will penetrate waves rather than slam in most sea states encountered in coastal Australian conditions. Because the design is lighter than heavy‑displacement cruisers, motion in short, steep chop can feel livelier; prudent sail selection and reefing keep motion and loads reasonable.
Australian sailing uses and conditions
Club racing: the Farr 11.6 is popular with club racers who want a competitive keelboat that still offers basic cruising comforts. Its upwind performance and manoeuvrability suit short offshore races and harbour series, while spinnaker work and sail inventory will determine competitiveness in local fleets.
Coastal cruising and weekend passages: the boat’s accommodation and tankage options allow comfortable coastal cruising with a small crew or family. For Australian conditions — where winds can shift quickly and seas can build — owners commonly fit modern sail control systems, stronger standing rigging and improved bilge and safety systems if they plan to cruise regularly.
Offshore: several Farr 11.6s have completed offshore races in their history. As with any older yacht, offshore capability depends heavily on maintenance, structural condition, and systems upgrades (navigation, communications, steering redundancy and safety equipment). Owners intending extended offshore work should invest in re‑rigging, up‑to‑date safety gear and thorough structural checks.
Principal strengths
- Balanced racer‑cruiser design that combines competitive performance with usable accommodation.
- Responsive helm and good upwind ability thanks to the fin keel and fractional rig.
- Comfortable motion for a boat of its displacement; generally sea kindly compared with contemporaries of similar length.
- Relatively straightforward systems and mechanical simplicity compared with modern, heavily‑systems yachts — easier to maintain for an owner‑operator.
- Strong aftermarket support and parts availability for common systems; the design is well known among classic Farr owners and race circles.
Limitations and compromises
- Older construction techniques and materials mean some boats require attention to deck core, blistering and past repairs; build quality varies by builder.
- Interior headroom and modern liveability features are limited compared with newer production cruisers of the same length.
- Original tankage, electrics and systems are often dated — comprehensive refits are common to bring older boats up to modern cruising expectations.
- Fixed fin keel and spade rudder can make grounding incidents more consequential; cost of repairing keel or rudder impacts can be significant.
Ownership, maintenance and refit
Routine ownership of a Farr 11.6 follows the normal pattern for boats of its age: attention to hull and deck integrity, standing rigging replacement cycles, engine service or repower, and periodic reconditioning of interior joinery. Important recurring maintenance items include checking for deck compressions around fittings, monitoring for osmotic blistering in older GRP, and inspecting keel bolts and the keel‑to‑hull joint for corrosion or movement.
Refit priorities for owners who cruise Australian waters frequently tend to be: new or serviced standing rigging, modern navigation and communications equipment, upgraded sail inventory (including a storm sail set), improved tankage and watermaker options for extended cruising, and safety gear upgrades for offshore capability. Owners who race will often invest in modern sailcloth, a high‑performance spinnaker wardrobe and deck layout changes such as repositioned winches or additional rope clutches.
What to inspect before buying
- Structural: survey for delamination, core rot (particularly in deck areas and coachroof), previous repair quality, and integrity of keel mounting/keel bolts.
- Keel and rudder: look for signs of grounding, keel movement, corroded bolts, or rudder play; check for any repairs around the rudder stock or skeg (if fitted).
- Rig and mast: record and date of last standing‑rigging replacement; mast condition, spreader ends, chainplate condition and deck penetration points where leaks or soft spots can develop.
- Engine and systems: engine hours, service history, and evidence of saltwater corrosion; condition of fuel and water tanks and plumbing; bilge pump capacity and output.
- Sails and deck gear: condition and age of main, headsails and spinnaker(s); winch condition and service history; functioning of furlers, halyard leads and clutches.
- Accommodation and tanks: check for damp, mould, odour indicating water ingress; verify hot water, toilet and plumbing operation; inspect electrical systems and batteries for age and condition.
- Documentation: builder’s plate or documentation confirming model designation (Farr 11.6 / Farr 38), ownership history, and any class or race modifications that may affect valuation or insurance.
Who this boat suits
The Farr 11.6 is best suited to sailors who want a genuine club‑racing capability in a boat that still offers practical accommodation for coastal cruising. It appeals to owners who appreciate a lively helm and upwind performance, and who are prepared to invest in maintenance or selective refits to keep systems current. Sailing couples or small families who cruise locally but enjoy occasional racing are a natural fit, as are experienced owners looking for a rewarding classic Farr hull to campaing or restore.
It is less suitable for owners who prioritise maximised interior volume, modern low‑maintenance systems, or those who require the absolute lowest maintenance solution; in those cases a newer production cruiser may be preferable. Similarly, those seeking trailerable convenience or shallow‑water gunkholing should look elsewhere: the fixed deep fin keel makes the Farr 11.6 a true keelboat rather than a trailer‑boat.
Sources consulted: sailboatdata.com, wikipedia.org, boatsales.com.au, mackenzieboating.com.au, cyca.com.au
