The Nacra 17 is a purpose‑designed Olympic mixed‑multihull. It was created when World Sailing selected a new one‑design multihull for Rio 2016 and Nacra, working with designers Morrelli & Melvin, produced a compact, stiff and light catamaran optimised for two sailors. Since its introduction the class has evolved from an initially partially lifting design to a full‑foiling configuration used by elite teams in World Cups, World Championships and the Olympic programme.
Although the Nacra 17 exists as a commercial product from Nacra Sailing, the boat is first and foremost a tightly regulated one‑design racing class. That affects choices owners make about sails, foils and systems: the emphasis is on repeatable set‑up, low weight and robust, repeatable foiling behaviour under racing loads rather than recreational comfort or cruising fit‑out.
Overview and design purpose
The brief for the Nacra 17 was explicit: produce a high‑performance multihull that met World Sailing’s specification for the 2016 Olympic mixed multihull event. The objective was not simply maximum speed but a controllable, modern platform that allowed men and women to race together — hence the boat’s righting‑moment and rig tuning are matched to a recommended mixed crew weight.
Design priorities were therefore lightness, longitudinal stiffness and a modern foil plan that could be developed as foiling technology matured. The resulting hull form is wave‑piercing and relatively narrow fore‑aft to reduce hobby‑horsing, while carbon spars, high‑aspect sails and shaped daggerboards give the boat power and lift. After Rio the class and manufacturer moved the platform to a full‑foiling mk2 specification (Z‑foil daggerboards and T‑rudders with elevators) to keep pace with developments in high‑speed multihull racing.
Designer, builder and production
The Nacra 17 was developed by Nacra Sailing in collaboration with US multihull designers Morrelli & Melvin. Nacra Sailing acts as builder and class supplier, producing the hulls, rigging, spars and control systems from their Netherlands facility. Morrelli & Melvin provided the naval architecture and foil design underpinning the original platform and its subsequent evolution.
Production began in the run‑up to the 2016 Olympic cycle. The class has since been manufactured in successive batches; importantly, the platform was revised after its Olympic debut and boats built around hull number 339 were transitioned to a full‑foiling four‑point configuration. Boats built earlier could be retrofitted to the new foil arrangement where permitted by class rules.
Construction and hull design
The Nacra 17 is built as a carbon‑reinforced sandwich structure using epoxy‑resin laminates. Hulls, crossbeams, daggerboards, rudders and spars are predominantly carbon with foam core in sections to control weight and stiffness. The overall platform was engineered to be highly longitudinally stiff so sail and rig forces translate into forward thrust rather than hull flex.
Hull shape follows a wave‑piercing philosophy — relatively fine bows and a narrow waterplane fore‑aft — which reduces pitching and maintains a steadier attitude when accelerating onto foils. The trampoline is tensioned between stiff crossbeams. Structural reinforcements were added in the mk2 evolution to cope with higher foiling loads and different foil locations.
Specifications
Cockpit, deck layout and sail handling
Cockpit and deck layout on the Nacra 17 are minimal and entirely race‑oriented. There is no enclosed cockpit; the crew operate from the trampoline and crossbeam areas. Control lines are led to easily accessed central organisers and cleats so the helm and crew can trim quickly while trapezing or controlling foils.
Primary controls include a mainsheet system with high purchase (commonly about 10:1), an adjustable mainsail Cunningham, jib cunningham and barber haulers or leads to set jib shape. The asymmetric downwind sail is gybed from the bowsprit; many boats use a snuffer/retriever for quicker hoists and douses at mark roundings. Trapeze wires for both helm and crew are standard; on‑water crew movement and rapid weight shifts are part of normal boat handling.
On the foiling mk2 boats the daggerboard/elevator rake and rudder elevator rake adjustments are critical for stable foiling. Class rules limit some systems to maintain one‑design control, so teams optimise trim and foil rake within those constraints rather than adding mechanical complexity.
Interior and accommodation
The Nacra 17 has no interior accommodation. It is an open catamaran where the structural crossbeams and trampoline form the platform for sailing. That absence of accommodation is deliberate: the boat is intended for regatta racing, short training sessions and events where people launch, race and recover the boat within a day. There are no berths, galley or head facilities and owners should not expect cruising comforts.
Sailing and handling
Handling a Nacra 17 is high‑performance and requires skill, athleticism and teamwork. In the earlier mk1 configuration the boat could plane and partially lift; in the mk2 full‑foiling set‑up the goal is to generate and maintain stable foiling both upwind and downwind. Foiling dramatically changes steering and trim demands: small inputs to rudder and foil rake produce large changes in height and pitch, so fine‑tuned coordination between helm and crew is essential.
Upwind performance on foils can be fast and remarkably efficient once the crew find the right foil incidence and sail trim. Downwind speeds are significantly higher than conventional cats of similar length — the gennaker and shorter bowsprit on the mk2 reflect the need to manage asymmetrical spinnaker loads at foiling speeds. At lower wind strengths the boat still offers lively planing performance, but it is in moderate to strong winds where the mk2 comes alive and separates itself from non‑foiling boats.
Balance is sensitive: because there is no ballast, righting moment comes from crew position and trapeze leverage. The craft rewards athletic crews with good weight distribution and rapid response to gusts; conversely, smaller or less experienced teams will find the platform demanding and less forgiving than heavier, more stable designs.
Australian sailing uses and conditions
In Australia the Nacra 17 is primarily a high‑performance racing choice for club and national regattas, international campaigns and training bases preparing for World Championships or Olympic selection. Its light weight makes it transportable by trailer and truck, which suits the long distances between events in Australia, but rigging, foil care and launching infrastructure need to be considered.
Typical local uses include coastal regattas in protected bays, lake regattas and open‑coast training where sea state is moderate. Because foiling exposes appendages to impact and high loading, crews sailing in Australian conditions should be mindful of debris, kelp and chop in shallow approach areas. Launch sites require ramps or dollies that allow clean launch/landing to avoid damaging daggerboards and rudder elevators.
Principal strengths
- Designed specifically as a modern Olympic multihull: tight one‑design controls and proven competitive pedigree.
- Lightweight carbon construction combined with a stiff platform translates rig and sail forces efficiently into speed.
- Full‑foiling mk2 geometry provides sustained high speeds and rewarding performance in the hands of trained crews.
- Relatively compact size (5.25m) makes transport and storage easier than larger Olympic multihulls.
- Strong class infrastructure and global event calendar support serious racers and national programmes.
Limitations and compromises
The Nacra 17 sacrifices versatility for top‑end performance. There is no accommodation, limited scope for recreational sailing and an elevated learning curve for safe and consistent foiling. Structural loads on a full‑foiling platform are high; older mk1 boats retrofitted to mk2 foils require careful inspection of laminate and core areas to ensure they can accept the altered load paths.
Maintenance and repair of carbon foils, rudder elevators and the carbon mast are more specialised and costly than typical small craft. The class rules restrict some systems, which keeps racing fair but limits owner‑level modifications to improve comfort or convenience.
Ownership, maintenance and refit
Owning a Nacra 17 is close to running a small performance campaign. Regular inspection of foils, daggerboard cases, rudder stocks and crossbeam attachments is mandatory because the rig and foils produce high cyclical loads. After foiling sessions crews should rinse foils and rudder elevators with fresh water and check for dings or core wetting.
Refit items that commonly appear on older boats include replacement of core or skin laminates where impact or delamination has occurred, renewed trampoline fabric, new bearings in rudder stocks and replacement blocks or running rigging that wears under race use. If older mk1 boats are converted to mk2 foils, a documented structural review and any necessary reinforcement of the daggerboard trunk and surrounding laminate should be undertaken.
What to inspect before buying
- Laminate condition around daggerboard trunks, crossbeam sockets and mast step for signs of impact, blistering or delamination.
- Condition and straightness of daggerboards, rudder blades and T‑elevators; check for core saturation or repaired impact points.
- Mast and boom for compression marks, crack lines or previous repairs in carbon sections; verify spar serial or build history where available.
- Trampoline and attachment webbing; look for UV degradation and wear at common load points.
- Running rigging, blocks and cleats – wear in blocks and Dyneema lines is typical and cheap to replace, but inspect for hidden chafe near through‑deck fairleads.
- If the boat has been converted between mk1 and mk2 configurations, request documented structural work and any factory or class‑approved modification paperwork.
- Evidence of impact history: ask about groundings, trailer incidents and contacts; high‑speed impacts can produce internal damage not obvious at first glance.
Who this boat suits
The Nacra 17 suits competitive sailors and national or high‑performance programmes whose primary aim is Olympic or international fleet racing. It demands athletic, technically capable crews who can rig, tune and maintain carbon foils and spars, and who relish the tactical and physical demands of short‑course multihull racing.
It is not a family daysailer or weekend cruiser. For clubs and individuals in Australia wanting to develop foiling skills, the Nacra 17 offers a direct pathway into elite multihull competition, but prospective owners should budget for specialist maintenance, spare foils and regular replacement of high‑wear components.
Sources consulted: nacrasailing.com, nacra17.org, sailboatdata.com, morrellimelvin.com
