Set aside a day. Have the workshop manual for your engine open; it gives the quantities, torques and filter numbers. This is the order that keeps the mess down.
What you need
- Oil and filter of the grade the maker specifies.
- Primary and secondary fuel filters.
- Impeller and gasket, drive belt, anodes if fitted.
- Oil extraction pump, filter wrench, rags, oil absorbent pads, a container for waste oil.
Step 1: warm the engine
Run it for ten minutes. Warm oil carries the dirt out and pumps easily.
Step 2: change the oil and filter
- Pump the oil out through the dipstick tube.
- Put a bag around the filter before unscrewing it.
- Oil the new filter's seal, fit it hand tight, refill to the mark.
Step 3: change the fuel filters
Do the primary, then the secondary, then bleed. There are separate tutorials for both jobs in this section.
Step 4: impeller
Pull it, inspect it and fit a new one each year. Keep the old one as a spare if it is sound.
Step 5: belt
Check for cracks and glazing. It should deflect about a centimetre under thumb pressure on the longest run. Black dust around the pulleys means it is slipping or misaligned.
Step 6: cooling
- Check the coolant level and its age. Replace it every two to three years or as the maker says.
- Replace the heat exchanger anode if your engine has one.
- Look for salt crust at hose joints and the exhaust elbow. Crust means a leak.
Step 7: air filter and breather
Clean or replace. A blocked filter costs power and makes black smoke.
Step 8: look and feel
- Engine mounts: no cracked rubber, nuts tight.
- Hoses: squeeze them. Soft or cracked hoses get replaced.
- Wiring: no green terminals, nothing chafing.
- Shaft seal and coupling: dry and tight.
- Gearbox oil level and colour.
Step 9: run and check
Start it, check for water at the exhaust, look for leaks at every filter you touched, then recheck the oil level.
Step 10: write it down
Date, engine hours, what you changed and part numbers. Take waste oil and filters to a marina or council collection point.
The order at a glance
Tools and parts to have ready
- Engine oil of the grade in the manual, and a little more than the sump holds
- Oil filter, primary and secondary fuel filters, impeller and gasket, air filter element if fitted
- Oil extraction pump, filter wrench, drip tray, oil absorbent pads
- Spare alternator belt and the spanners to change it
- Anodes for the engine and heat exchanger if yours has them
- Coolant of the type the maker specifies. Do not mix types.
How often
| Job | Typical interval |
|---|---|
| Engine oil and filter | Every 100 to 150 hours or once a year |
| Fuel filters | Every 200 to 250 hours or once a year |
| Impeller | Inspect yearly, replace every one to two years |
| Belt tension and condition | Every 50 hours |
| Engine anodes | Inspect every 100 hours |
| Coolant | Every two to three years |
| Gearbox oil | Yearly, or as the manual says |
These are typical figures. Your engine manual wins every time. A boat that does 30 hours a year still needs the yearly service, because oil ages and collects acid whether you motor or not.
Mistakes to avoid
- Changing oil cold. Run the engine for ten minutes first so the oil carries the dirt out with it.
- Overfilling. Add most of the oil, run the engine, wait, then top up to the mark.
- Forgetting to open the seacock after working on the raw water side.
- Throwing the old impeller away without counting the blades. A missing blade is sitting in the heat exchanger.
- Not bleeding the fuel system after the filters and then wondering why it will not start.
After the service
Run the engine at the dock for fifteen minutes under load in gear. Check for water at the exhaust, oil pressure, charging voltage and any drips at the filters you touched. Look again after the first hour of real use. Write the engine hours and the date in the log and on the oil filter with a marker.
Calculator
Safety gear service date
Work out when an item is next due from the date on its label or certificate.
- Enter a date
