A sail does not have to be torn to be finished. Cloth stretches with every season of sun and load. The shape goes deep and the draft moves aft. The boat heels more, makes more leeway and points lower, and you put up with it because it happened slowly.
New sails fix that in a day. For a boat that sails rather than motors, nothing else you can buy changes more.
Signs your sails are done
- The boat heels early and you reef sooner than you used to.
- You cannot flatten the mainsail, however hard you pull on the outhaul and backstay.
- The headsail has a hooked or fluttering leech you cannot tune out.
- The cloth feels soft like a bedsheet, and the stitching is chalky or broken along the leech and foot.
- The sun strip on a furling headsail is faded through and the cloth under it is brittle.
- You have had it repaired more than twice in one season.
Cloth
| Cloth | Holds its shape | Lasts | Cost | Suits |
|---|---|---|---|---|
| Woven polyester (Dacron), cross cut | Fair | Very long | Lowest | Most coastal cruising boats |
| Premium woven polyester, radial or cross cut | Good | Long | Middle | Cruisers who want better shape for more years |
| Cruising laminate | Very good | Shorter, and dislikes damp storage | Higher | Performance cruisers and club racers |
| Membrane or moulded | Best | Depends on build | Highest | Racing and fast cruising |
For most cruising boats a good woven polyester is the right answer. It forgives abuse, repairs easily anywhere and lasts. Pay for better cloth before you pay for fancier construction.
Mainsail choices
- Slab reefing with a stack pack and lazy jacks gives the best shape for the money and is simple to fix.
- Full battens hold shape, quieten the sail and help it drop into the pack. Use good batten cars on boats over about 11 metres, or the sail will be hard to hoist and lower.
- In mast furling is convenient and costs you sail area and shape. Vertical battens win some of it back.
- In boom furling keeps a better shape than in mast, but it is fussy about boom angle when you furl.
- Ask for three reefs if you go offshore. The third reef replaces a trysail on many cruising boats.
Headsail choices
- A furling genoa of about 135 percent is the all round cruising choice in light air areas.
- A 100 to 110 percent jib is easier to tack, sets better when partly furled and suits windier waters.
- No sail sets well deeply furled. A foam or rope luff helps. If you often sail in strong wind, a separate staysail on an inner forestay beats a heavily rolled genoa.
- Check the sun protection strip. It is cheaper to replace the strip on time than the sail.
Downwind sails
- An asymmetric spinnaker or gennaker in a sock, or on a top down furler, turns slow light air days into sailing. It is the most useful extra sail for a cruiser.
- A code zero covers close reaching in light air. It is useful, but not the first thing to buy.
- For trade wind passages, twin poled out headsails are simple and can be reefed from the cockpit.
Getting it right with the sailmaker
- Have the sailmaker measure the boat. Do not order from the old sail's sizes or the class figures.
- Say how you really sail: where, how many crew, how much wind you go out in, how long you want the sails to last.
- Have the rig tuned before measuring. Sails cut for a slack rig will never set right.
- Ask what cloth, weight and brand is quoted, so you can compare quotes fairly.
- Ask for a sea trial or a fitting check after delivery, and who does local repairs.
Looking after new sails
- Rinse salt out and dry them before long storage.
- Keep the sun off. Use covers every time, not only for long stays.
- Do not let sails flog. Flogging does more damage in minutes than weeks of sailing.
- Have them checked and restitched every year or two. Stitching fails long before cloth.
Know your numbers
Sailmakers talk in four rig measurements. I is the height of the foretriangle, J is its base, P is the mainsail luff and E is the mainsail foot. With those you can estimate areas and compare quotes.
Calculator
Sail area from rig measurements
Estimate mainsail and headsail area from the standard rig dimensions.
- 24 m²
- 35.1 m²
- 59.1 m²
Calculator
Sail area to displacement ratio
How much sail a boat carries for its weight.
- 16.7
- Cruiser
Reefing
Calculator
How much sail to carry
Wind force rises with the square of wind speed. This shows the sail area that gives the same heeling force as your full sail does in the breeze where the boat feels right.
- 24.3 m²
- 40%
- 2.5 times
What sails cost, in plain terms
Price follows area, cloth and construction. A woven polyester cross cut sail is the base price. Radial construction in better cloth costs noticeably more, and a membrane sail can be double. Extras add up: a third reef, a foam luff, UV strip, batten cars and a stack pack are each separate lines on a quote. Ask for every quote on the same specification, or you are comparing different sails.
The words sailmakers use
- Luff, leech, foot: the front, back and bottom edges.
- Draft: the depth of the curve. Draft position is how far back the deepest point sits.
- Roach: mainsail area outside a straight line from head to clew, held out by battens.
- LP: luff perpendicular, the shortest distance from clew to luff. A 135% genoa has an LP of 1.35 times J.
- Cross cut: panels run across the sail. Simple, economical, right for woven cloth.
- Radial or tri radial: panels fan out from the corners along the load lines. Holds shape better and needs cloth made for it.
- Cloth weight: stated in ounces or grams per square metre. Heavier lasts longer and sets worse in light air.
- UV strip: sacrificial cloth on the leech and foot of a furling sail.
Choosing cloth weight
Go by boat size and where you sail, then let the sailmaker adjust. As a guide for woven polyester on a cruising boat: around 6 to 7 ounce for 9 to 10 metres, 7 to 8 ounce for 10 to 12 metres, 8 to 10 ounce for 12 to 14 metres. Go a step heavier for offshore work and for the mainsail if it is your storm sail too.
Extras worth paying for
- A third reef in the main for offshore boats.
- Leech and foot lines with cleats you can reach when reefed.
- A foam or rope luff pad on a furling genoa.
- Spreader and stanchion chafe patches.
- Telltales on the luff of the headsail and the leech of the main.
- Triple stitching in UV resistant thread on offshore sails.
- Draft stripes, so you can see and photograph the shape.
Extras you can skip
- Exotic fibres on a boat that cruises at six knots.
- A full batten main without proper cars on a bigger boat. It will jam.
- Oversized genoas in windy waters. You will sail it rolled, badly, most of the time.
Rig first
New sails on a slack or bent rig are wasted. Before ordering: check forestay tension, mast straightness and pre bend, and that the furler and halyard swivels turn freely. A rigger's tune costs little next to a suit of sails.
Second hand and stock sails
A good used sail from a sail broker can be a cheap spare or a way to try a size before buying new. Check measurements against your I, J, P and E, and expect to pay a sailmaker for a recut and new luff tape. Stock production sails cost less than custom ones and fit common production boats well.
Common questions
How long do cruising sails last? A woven polyester sail holds together for 10 to 15 years of seasonal use. Its shape is usually gone well before that, often after 5 to 8 years or about 3,000 to 4,000 hours.
Can an old sail be recut? Once, sometimes. A recut removes stretched cloth along the luff and helps for a season or two. It cannot restore cloth that has gone soft.
Should I replace the main or the headsail first? The one in worse shape. If they are equal, the headsail, because it drives the boat upwind and gets the most sun on a furler.
Is a laminate sail worth it for cruising? Only if you value performance and will keep it dry and covered. For most cruisers premium woven cloth gives more years per dollar.
Tutorials
Step by step guides are listed at the top of this page and in the sidebar: checking your sails, measuring for a quote, reefing, sail care, and choosing a downwind sail.
