An autopilot is crew that never tires. An undersized one gives up when the sea gets up, which is when you need it.
Step 1: get the real weight
Use loaded cruising displacement, not the brochure figure. Add water, fuel, stores, anchors, dinghy and crew. Many cruisers are 20 to 30% over the listed weight. Choose a drive rated for at least that figure, with margin.
Step 2: match the drive to the steering
- Tiller boats up to about 4 or 5 tonnes: a tiller pilot. Cheap, exposed, carry a spare.
- Wheel pilot on the pedestal: for light boats and motoring only. Not for offshore work.
- Below deck linear drive on the quadrant or a tiller arm: the standard for cable and rod steering.
- Hydraulic pump: for boats with hydraulic steering.
- Rotary drive: for chain and wire systems where a linear drive will not fit.
Step 3: check the mounting
A below deck drive pushes with hundreds of kilos of force. It needs a rudder stock fitting and a hull mounting point built for that. Budget for the fabrication.
Step 4: choose the brain and sensors
- A modern heading sensor with gyro stabilisation steers far better in a seaway than an old fluxgate compass.
- A rudder feedback sensor improves steering and is required by many systems.
- Wind mode steers to an apparent wind angle. On a sailing boat it is worth having.
Step 5: plan the power
A below deck pilot averages 2 to 6 amps under sail, more when the boat is badly balanced. Reef and trim for balance and the draw halves.
Calculator
Electronics power use
What the navigation gear draws over a day on passage.
- 146 Ah
- 6.1 A
Step 6: plan for failure
- Carry a spare drive belt, brushes or the spares the maker lists.
- Know how to disconnect the drive and hand steer.
- For ocean passages, a wind vane or a second pilot is the proper backup.
Questions for the seller
- Maximum displacement for this drive, and at what rudder load?
- Hard over time for my boat?
- Does it share data with my plotter brand?
- Who services it here?
The parts
Drive types compared
| Type | Suits | Limits |
|---|---|---|
| Tiller pilot | Tiller boats up to about 4 to 6 tonnes | Exposed in the cockpit, struggles when overpowered |
| Wheel pilot | Lighter wheel steered boats, coastal use | Belt or gear drive wears, limited power |
| Below deck linear drive | Most cruising boats with a quadrant | Needs a strong mounting point |
| Hydraulic ram and pump | Heavier boats, hydraulic steering | More parts, more installation |
| Windvane | Offshore sailing with no power use | Steers to the wind, not a course. Not for motoring |
Size it for the worst day
Makers rate drives by displacement. Use the loaded cruising displacement of your boat, not the brochure figure, then add a margin of about 20 percent. Fuel, water, anchor chain, a dinghy and stores can add a tonne or two. A pilot that is right at its limit steers well in flat water and gives up surfing down a wave at night, which is when you need it.
Power use
A below deck pilot on a well balanced boat may average 2 to 4 amps. The same pilot fighting weather helm can draw several times that. Reefing early and trimming for balance is the cheapest way to cut autopilot power. Add it to your energy budget for a full day on passage, not just the daylight hours.
Calculator
Electronics power use
What the navigation gear draws over a day on passage.
- 146 Ah
- 6.1 A
Mistakes to avoid
- Mounting the drive to a thin bulkhead. The loads are high and they reverse constantly.
- Putting the compass or heading sensor near the engine, speakers or tools.
- Skipping the dockside and sea trial calibration.
- No backup. Carry spare belts or a spare tiller pilot, and know how to disengage the drive quickly.
- Leaving the watch to the pilot. It steers. It does not look out.







