A sailmaker should measure the boat before cutting cloth. You still need your own figures to get comparable quotes and to check theirs.
The four rig measurements
- I: from the top of the forestay attachment down to the deck at the mast.
- J: from the front of the mast to the forestay at the deck.
- P: from the top of the boom to the highest point the mainsail can hoist.
- E: from the back of the mast to the furthest point the clew can go on the boom.
Use a long steel tape hoisted on a halyard. Do it on a calm day with someone holding the bottom end.
Calculator
Sail area from rig measurements
Estimate mainsail and headsail area from the standard rig dimensions.
- 24 m²
- 35.1 m²
- 59.1 m²
Mainsail details
- Slide or bolt rope, and the size of the mast track. Take a spare slide or a photo with a ruler.
- Tack and clew fittings, and the tack set back from the mast.
- Number and position of reefs you want, and how they are led.
- Backstay position, so the roach clears it.
- Batten type, and whether you want cars.
Headsail details
- Furler make and model, and the luff tape size it takes.
- Maximum hoist: head swivel at the top to tack drum.
- Track positions, so the sheet lead can be reached for the size you want.
- Spreader and pulpit positions, for chafe patches.
Photos to send
- The whole rig from the side.
- The mast track, gooseneck, furler drum and head swivel, close up.
- The old sails flying, from below.
Write a one page brief
- Where you sail and in how much wind.
- Crew, and how the boat is reefed.
- Priorities: longevity, performance, ease of handling. Rank them.
- Cloth type you want quoted, and the extras to include.
Send the same brief to each sailmaker. Then the prices compare.
Before the measure
Have the rig tuned and the furler working properly. A sail cut for a slack forestay will never set once the rig is right.
What you need
- A 30 metre steel or fibreglass tape. Cloth tapes stretch.
- A halyard to hoist the tape, with a downhaul line tied on so you can get it back
- A calm day with the boat level
- A helper, paper and a camera
- The sailmaker own measurement form. Use theirs, because each loft asks for things slightly differently.
The rig dimensions
| Letter | What it is |
|---|---|
| I | Height of the foretriangle, from the sheer line to the top of the jib halyard sheave |
| J | Base of the foretriangle, from the front of the mast to the forestay at the deck |
| P | Mainsail luff, from the top of the boom to the highest point the main can be hoisted |
| E | Mainsail foot, from the back of the mast to the outhaul limit on the boom |
Published figures for your class are a starting point only. Masts get changed, booms get replaced and furlers get fitted. Measure the boat in front of you.
Calculator
Sail area from rig measurements
Estimate mainsail and headsail area from the standard rig dimensions.
- 24 m²
- 35.1 m²
- 59.1 m²
Details the sailmaker will ask for
- Luff fitting: slides, slugs, bolt rope or cars, with the size of the track or groove
- Tack and clew setback and height
- Reef positions and how each reef is tied down
- Backstay position, for mainsail roach
- Furler make and model, luff groove size, and the drum height off the deck
- Sheeting position and track length for headsails
- Spreader length and height, so the genoa can be patched where it touches
Mistakes to avoid
- Measuring the old sail. It has stretched and may never have fitted.
- Measuring with the halyard not fully hoisted.
- Forgetting the sag in the tape on a long run. Pull it firm and say so on the form.
- Guessing a number. If you could not measure it, write that down and let the sailmaker decide.
- Not taking photos of the tack, clew, masthead and boom end. A photo answers questions a number cannot.
When to let the sailmaker measure
For a racing sail, a boat with an unusual rig, or any sail where fit matters to the centimetre, ask the loft to measure. Many will do it free with an order. If the loft measured and the sail does not fit, it is their problem. If you measured, it is yours.
