A good patch outlasts the dinghy. A bad one peels in a week. The difference is preparation and using the adhesive made for your fabric.
Step 1: find the leak
- Inflate hard. Brush soapy water over the tube and watch for bubbles.
- Check valves first. A gritty or loose valve is the most common slow leak, and needs cleaning or a new seal, not a patch.
- Check seams and the transom joint. Seam leaks are a professional repair.
- Mark the hole with a pen.
Step 2: identify the fabric
- Look inside the tube through the valve, or at the back of an offcut. PVC is the same colour and shiny on both sides. Hypalon type fabric is dull, with a dark grey or black inner face.
- Sand a hidden spot lightly. Hypalon scuffs to a matt powder. PVC only scratches.
- The builder's plate or manual will say.
Step 3: get the right materials
- Patch material of the same fabric.
- Two part adhesive for that fabric. PVC glue does not hold Hypalon, and the reverse is also true. One part glue is for emergencies only.
- Solvent: MEK for PVC, toluene or the maker's primer for Hypalon. Use gloves and work in moving air, away from flame.
Step 4: prepare
- Work in the shade, in dry air, between about 15 and 25°C. Humidity ruins the bond.
- Deflate the tube and lay it flat.
- Cut a round or round cornered patch that overlaps the hole by at least 5 cm all round.
- Trace it on the tube and mask around the line.
- PVC: wipe both surfaces with solvent. Hypalon: sand both to a matt finish, then wipe.
Step 5: glue
- Mix the adhesive exactly as directed.
- Brush a thin coat on both surfaces. Let it dry until tacky, about 20 minutes, then a second thin coat.
- When the second coat is just tacky, lay the patch from one edge, pressing air out.
- Roll it down hard with a roller or the back of a spoon.
- Remove the tape.
Step 6: wait
Leave it 24 hours before inflating, 48 before full pressure. This is the step people skip.
Tears and big holes
Anything over about 5 cm needs an inside patch as well as an outside one. Carry a clamp style emergency plug for getting home, and do the proper repair ashore.
Carry a kit
Patches, two part glue in date, solvent, sandpaper, a roller, a spare valve and valve tool. Check the glue date each season. It goes off.
What you need
- Patch material that matches the boat: PVC or Hypalon type. They are not interchangeable.
- The right adhesive for that fabric. Two part adhesive lasts far longer than the one part tube in a basic repair kit.
- Solvent for cleaning: the adhesive maker will name it
- Fine sandpaper for Hypalon type fabric
- Soapy water in a spray bottle, a pencil, scissors, a roller or the back of a spoon, masking tape
PVC or Hypalon: how to tell
Look at the inside of the fabric through the valve. If the inside is the same colour and glossy like the outside, it is probably PVC. If the inside is dark grey or black and matt, it is probably a Hypalon type. A welded seam also suggests PVC, and a glued, overlapped seam suggests Hypalon. Check the maker plate if in doubt, because the wrong glue will not hold.
Conditions matter
Glue fails in humidity and heat. Work in shade, on a dry day, with the tube deflated and flat. Most adhesives want low humidity and a moderate temperature, so early morning in the tropics is the time. Follow the waiting times on the tin exactly. Rushing the tack time is the most common reason patches lift.
Mistakes to avoid
- A patch that is too small. Allow at least 25 millimetres all round the damage, with rounded corners.
- Not cleaning past the edge of the patch.
- Inflating to full pressure the same day. Give it 24 hours, longer for two part glue.
- Patching a seam or a valve base yourself. Those are jobs for a repairer.
- Ignoring the cause. Find the oyster shell, the sharp fitting or the chafe point.
A temporary fix to get home
For a small hole, a self adhesive emergency patch or good repair tape on a clean, dry surface will usually hold for days. Treat it as temporary and do the proper repair when you can.











